32 mm2/sec ISO VG Öle

Mobil SHC 632

Mobil Industrial

Exceptional Performance Gear and Bearing Oils

Most important applications of Mobil SHC 632 are:

• + Filled for life gearboxes, especially high ratio/ low-efficiency worm gears
• + Remotely located gearboxes, where oil change-out is difficult
• + Low temperature applications, such as ski lifts where seasonal oil changes can be avoided
• + Mixer roll bearings and roll neck bearings where high temperatures are encountered
• + Plastic calenders
• + Severe centrifuge applications, including marine centrifuges
• + Railroad A/C Traction Drives
• + Mobil SHC 632 is approved by Siemens AG for use in Flender gearboxes
   

Pay attention! Price of Mobil SHC 632 drops automatically with higher volumes.

CASSIDA FM HYDRAULIC OIL 32

Hydraulic fluids for food and beverage processing equipment

CASSIDA FM HYDRAULIC OIL 32 applications:

Hydraulic systems, Hydrostatic gears, Plain and anti-friction bearings, General purpose lubrication including light duty gearboxes, Circulating oil systems

Please note!! Price of CASSIDA FM HYDRAULIC OIL 32 drops automatically in larger quantities.

Klüber Summit SH 32

Synthetic air compressor oils for oil change intervals up to 10,000 operating hours

Application Klüber Summit SH 32

Klüber Summit SH oils have been designed especially for the lubrication of highly loaded, oil-injected screw-type compressors with oil change intervals up to 10,000 operating hours. Klüber Summit SH oils can also be used for compressors that were previously run with mineral oils. They are neutral towards most elastomer seals used in air compressors, therefore leakage is not to be expected. Klüber Summit SH 32 is especially suitable for centrifugal compressors and Klüber Summit SH 100 for reciprocating piston compressors. Klüber Summit SH oils offer good oxidation stability due to the synthetic base oil, thus minimizing oxidation residues in the compressors and extending oil change intervals and the service life of oil filters and separators. Special inhibitors contained in the oils keep the inside of compressors clean. Owing to the evaporation stability of the base oil, the oil vapour content in the compressed air can be considerably reduced compared to conventional mineral oils. This contributes to a reduction of oil consumption and clean compressed air; gumming of pneumatic valves in the compressed air circuit can be prevented as well due to the low oil content of the Klüber Summit SH oils.

FM HEAT TRANSFER FLUID 32

Heat transfer fluid for use in food manufacturing industry

FM HEAT TRANSFER FLUID 32 main applications:

• Heat transfer systems with a bulk oil temperature range of approximately -10 °C to max. +325 °C where the surface temperature of the heating elements (oil fi lm temperature) should not exceed +340 °C.

FM HEAT TRANSFER FLUID is designed for closed circuit and pressureless heat transfer systems. It is based on a careful blend of highly refi ned oils and additives chosen for their ability to meet the stringent requirements of the food industry.

Your advantage! Price of FM HEAT TRANSFER FLUID 32 drops automatically in larger quantities.

Mobil SHC Gargoyle 32 previously Mobil EAL Arctic 32

Refrigeration compressor oils

Application Mobil SHC Gargoyle 32

Application considerations: Mobil SHC Gargoyle 32 oils are hygroscopic and measures must be taken to prevent the absorption of moisture. Packages should be tightly sealed when not in use and small packages are preferred. The product should not be placed in a plastic container if this can absorb moisture. Mobil SHC Gargoyle 32 oils are recommended for refrigeration systems where refrigerants containing HFC or carbon dioxide are used. Typical applications are: Domestic refrigeration such as refrigerators, freezers, air conditioners and heat pumps. Commercial refrigeration systems such as air conditioners in offices, shopping centres and hotels and in mobile refrigeration systems. Industrial applications such as food preparation and freezing and refrigeration applications.

CASTROL Optileb HY 32

Food grade hydraulic oils

Application CASTROL Optileb HY 32

For the special applications in the food and beverage industries where there may be exposure of the lubricated part to the edible product or its packaging For hydraulic systems in production, filling and packaging machines

Klübersynth GH 6-32

Synthetic high-performance gear and high-temperature oil with KlüberComp Lube Technology

Application Klübersynth GH 6-32

Klübersynth GH 6 oil was especially developed for the lubrication of worm gears with steel/bronze or steel/grey cast iron pairings. Klübersynth GH 6 oil is also used for the lubrication of bevel and spur gears, rolling and plain bearings as well as all types of toothed couplings, especially when exposed to high temperatures. It can also be used for the lubrication of lifting, drive and transport chains

Cassida Fluid HF 32 Previous Name: Shell Cassida 32

Hydraulic fluids for food manufacturing machinery

Cassida Fluid HF 32 main applications:

• Hydraulic systems
• Hydrostatic gears
• Plain and anti-friction bearings
• General purpose lubrication including light duty gearboxes
• Circulating oil systems

Cassida Fluid HF 32 are high performance, anti-wear multipurpose lubricants, specially developed for use in machinery used in the food and beverage processing and packaging industry. They are based on a careful blend of synthetic fluids and selected additives chosen for their ability to meet the stringent requirements of the food industry.

RENISO TRITON SEZ 32

Synthetic refrigeration oils based on polyol esters (POE) for HFC/FC refrigerants

RENISO TRITON SEZ 32 field of applications:

The RENISO TRITON SE/SEZ series is outstandingly suited for all refrigeration circuits, in which chlorine-free HFC/FC refrigerants, e.g. R134a, R404A or R410A are used. Depending on the viscosity, RENISO TRITON SE/SEZ refrigeration oils are recommended for hermetical, semihermetical and open piston compressors and for screw-type and turbo-compressors. RENISO TRITON SEZ 22 is especially suitable for deepfreeze systems operating with R23

Please note!! Price of RENISO TRITON SEZ 32 drops automatically in larger quantities.

Cassida Fluid DC 32

Speciality direct contact fluid for food processing applications in the food manufacturing industry

Cassida Fluid DC 32 main applications:

• Absorber oil for edible oil extraction plant solvent recovery systems.
• Forming oil for the manufacture of both two and three piece cans for food and beverages.
• Heat transfer systems in the food industry with a bulk oil temperature range of approximately -30°C to +280°C where the surface temperature of the heating elements (oil film temperature) should not exceed +320°C.

Cassida Fluid DC 32 is a multipurpose fluid designed for a number of special applications in the food manufacturing industry, including absorber oil for edible oil solvent recovery systems, canforming and closed circuit/pressureless heat transfer systems. Cassida Fluid DC 32 has been specially developed to meet the stringent requirements of the food industry. Cassida DC 32 is based on a careful blend of synthetic fluids chosen for their ability to meet the stringent requirements of the food industry.

Your advantage! Price of Cassida Fluid DC 32 drops automatically in larger quantities.

Klübersynth GEM 4-32 N

Synthetic high-performance gear and multipurpose oil with KlüberComp Lube Technology

Application Klübersynth GEM 4-32 N

Klübersynth GEM 4 N was specially developed for the lubrication of spur, bevel, hypoid and planetary gears that are subject to high loads. Such gears are frequently used in the wind, steel, mining and sugar industries. It is also used for the lubrication of standard worm gears as defined in DIN 3996. Klübersynth GEM 4 N can also be used for the lubrication of plain and rolling bearings, all kinds of toothed couplings, chains, guideways, joints, spindles and pumps, especially in applications where the equipment is exposed to elevated temperatures or pronounced temperature fluctuations.

CASTROL Hyspin ZZ 32

Hydraulic oil for the highest demands

Application CASTROL Hyspin ZZ 32

The Hyspin ZZ range are formulated for applications requiring anti-wear and superior oxidation performance and are particularly suitable for hydraulic systems using vane and piston pumps where elevated operating temperatures are encountered. They are formulated for use in severely stressed systems in which high levels of anti-wear performance and/or ultra fine filtration are required. They have been proven to be resistant to the effects of ‘dieseling’ in highly stressed systems such as plastic injection moulding and fatigue testing equipment where the application leads to rapid breakdown of more conventional products. The range is fully compatible with elastomer materials commonly used for static and dynamic seals, such as nitrile, silicone and fluorinated (e.g. Viton) polymers.

Hyspin ZZ is classified as follows:

• DIN 51502 classification - HLP
• ISO 6743/4 - Hydraulic Oils Type HM

Hyspin ZZ grades meet the requirements (for appropriate viscosity grade) of:

• DIN 51524 Part 2
• Cincinnati Lamb (Milacron) P 68-69-70
• Denison (Parker Hannafin) HF-0
• US Steel 126 & 127
• Eaton (formerly Vickers) I-286-S & M-2950-S
• Bosch Rexroth RE90220

Your advantage! Price of CASTROL Hyspin ZZ 32 drops automatically in larger quantities.

TOTAL AZOLLA AF 32

Antiwear, ashless hydraulic oils

Applications TOTAL AZOLLA AF 32

• Hydraulic systems operating under high pressure and/or temperature conditions.
• High-pressue vane, piston or gear pumps.
• Sensitive hydraulic circuits requiring absolute filterability of the fluid (very fine servo valve play) : plastic moulding machines.
• Any hydraulic system where the risk of contamination of the environment and waters exists.
• Any application where an antiwear, high-performance oil is necessary : various movements, plain bearings and rolling bearings, reducers under low load, etc. .
• Lubrication of circuits in which the presence of water is accidental : machine tools, farm and food products industries, paper mills, steel making, etc.

Your advantage! Price of TOTAL AZOLLA AF 32 drops automatically in larger quantities.

TOTAL PRESLIA GT 32

High performance long life gas turbine oils for severe applications

Applications TOTAL PRESLIA GT 32

PRESLIA GT oils are:

• specially designed for the lubrication (bearings, gear boxes) and control circuit of steam and gas turbines
• turbines submitted to high thermal stress
• suitable for turbine coupled gears lubrication

Your advantage! Price of TOTAL PRESLIA GT 32 drops automatically in larger quantities.

TOTAL CIRKAN RO 32

R and O type machine oils.

Applications CIRKAN RO 32

CIRKAN RO oils are mineral oils containing additives with appropriate viscosities for lubricating moving parts operating under severe temperature conditions:

• fluid grades: systems operating at high speed: textile machinery, machine tools, and hydraulic circuits requiring a category HL oil.
• viscous grades: lubrication of bearings and gears not requiring anti-wear and extreme-pressure properties.

Your advantage! Price of TOTAL CIRKAN RO 32 drops automatically in larger quantities.

Shell Tellus S4 VE 32

Advanced Synthetic Gas To Liquid (GTL) Zinc Based Hydraulic Oil

Application Shell Tellus S4 VE 32

Mobile Hydraulic systems. Shell Tellus S4 VE, with its broad operating window, long oil drain intervals, superior system operation characteristics and many OEM approvals, is designed to be particularly suitable for mobile hydraulic systems such as construction and mining machinery

Industrial hydraulic systems. Shell Tellus S4 VE, with its energy efficiency benefits and long oil life, is designed to be particularly suitable for stationary industrial hydraulic systems with a high intensity of hydraulic power usage such as injection molding and high pressure metal pressing operations

Wind Turbines. Wind turbine systems are exposed to harsh conditions such as extreme cold climate and humid regions including offshore locations. Shell Tellus S4 VE with its high performance additives in GTL base oil enables long service life and its high viscosity index delivers responsive performance even in cold start conditions

Marine Hydraulic Systems. Shell Tellus S4 VE is recommended for marine applications where ISO HV category hydraulic fluids are recommended

Mobil DTE 732

Premium Turbine Oils

Application Mobil DTE 732

Mobil DTE 700 Series are designed to meet or exceed the requirements of circulation systems of steam and gas turbines. Specific applications include Electric power generation for high output base load utilities. Gas Turbine Combined Cycle Power Plants operating in base load or peak generation modes. Gas turbines in Captive Power plants. Gas or steam turbine prime movers. Hydroelectric turbine applications

Mobil DTE 832

Superior Performance Turbine Oils

Application Mobil DTE 832

Mobil DTE 832 and 846 are superior performance turbine oils designed for use in steam and gas turbine oil systems, direct- or gear-coupled and turbine speed control mechanisms. Specific applications include: Combined cycle (CCGT) electric power generation applications including those with a common circulation system for the steam turbine and gas turbine. Lubrication of steam turbine or gas turbine units used for electric power generation, natural gas pipeline transmission, process operations and cogeneration plants.

Houghton Macron 400 M-32

Properties

Macron 400 M-32 is based on hydro treated mineral oil with low aromatic content. A combination of polar, extreme pressure and anti-wear additives provide the oil with high load carrying properties. The oil provides good surface finish of the machined work pieces.

Macron 400 M-32 is free from zinc, chlorine and active sulphur.

Applications

Macron 400 M-32 is a high performance cutting oil for operations on light and medium alloyed steels, aluminium and yellow metals.

Macron 400 M-32 has multipurpose oil characteristics for cutting and hydraulic oil HLP DIN 51524-2 and gear oil CLP DIN 51517-3.

It has a good de-aeration power, does not foam and is not aggressive for the paints on machine tools.

MACRON 400 M-32 is based on hydro treated mineral oil with low aromatic content. A combination of polar, extreme pressure and anti-wear additives provide the oil with high load carrying properties. The oil provides good surface finish of the machined work pieces.

MACRON 400 M-32 is free from zinc, chlorine and active sulphur. 

Advantages:

• Increased productivity - reduced machine downtime.
• Reduced cost - long sump life.
• Secure handling - fulfills HLP 1 CLP standards.
• Secure handling - high EHS standard.

Shell Tellus S4 ME 32 Previous Name: Tellus EE

Advanced Synthetic Industrial Hydraulic Fluid

Shell Tellus S4 ME 32 main applications:

• Industrial hydraulic systems
• Mobile hydraulic systems
• Environmental impact

Shell Tellus S4 ME 32 hydraulic fluids are designed to help users improve the energy efficiency of their hydraulic systems without compromising the protection of the system or maintenance procedures of their equipment and operations. Shell Tellus S4 ME 32 has been demonstrated to improve energy efficiency in a wide range of applications such as plastic injection moulding, metal pressing, and mining conveyors. In addition, Shell Tellus S4 ME 32 is also designed to help equipment service life and lower maintenance costs through providing outstanding wear protection and long oil life capability

Please note!! Price of Shell Tellus S4 ME 32 drops automatically in larger quantities.